Dieser befindet sich auf der hinteren Umschlagseite dieser. Per l'installazione e i collegamenti, fare riferimento al manuale di istruzioni per. Zie voor het monteren en aansluiten van het apparaat de bijgeleverde handleiding "Installatie.
Previous Page. Next Page. Thank you for purchasing this Sony Compact Disc Player. Page 3: Table Of Contents Setting the clock Page 5: Precautions If you have any questions or problems concerning your unit that are not covered in this manual, please consult your nearest Sony dealer. Moisture condensation On a rainy day or in a very damp area, moisture condensation may occur inside the lenses and display of the unit. Note on DualDiscs This product has been engineered to provide the highest entertainment value while playing standard CD discs.
Page 7: Getting Started Getting Started Resetting the unit Before operating the unit for the first time, or after replacing the car battery or changing the connections, you must reset the unit. Page 8: Setting The Clock Attaching the front panel Attach part A of the front panel to part B of the unit as illustrated and push the left side into position until it clicks.
Note Do not put anything on the inner surface of the front panel. Playback starts automatically. Page Playing Tracks Repeatedly Playing tracks repeatedly — Repeat Play The current track will repeat itself when it reaches the end.
Repeat Play starts. Press MODE repeatedly to select the band. Press the number button 1 to 6 on which the desired station is stored. For example, one of the following will be displayed upon receiving a station with RDS capability.
If the unit cannot find the same PI, the unit returns to the previously selected frequency. You can select a different setting for AF, TA, or both for individual preset stations, or the same setting for all preset stations. The current programme type name appears if the station is transmitting the PTY data. You can store a different equalizer setting for each source. Page Additional Information If the fuse blows again after replacement, there may be an internal malfunction.
In such a case, consult your nearest Sony dealer. Warning Never use a fuse with an amperage rating exceeding the one supplied with the unit as this could damage the unit. Orient the release key correctly. Remove the unit. Page Troubleshooting Troubleshooting The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures.
General No sound. If these solutions do not help improve the situation, consult your nearest Sony dealer. Page 24 Willkommen! Fassen Sie CDs nur am Rand an.
Hinweis Legen Sie auf der Innenseite der Frontplatte nichts ab. Die Wiedergabe beginnt automatisch. Repeat Play beginnt. Wenn das Einstellen gespeicherter Sender nicht funktioniert — Notice that the minus side of a tantalum capacitor may be dam- aged by heat. This label is located on the bottom of the chassis. When replacing the chassis T. The following test discs should be used to check the capability:. These marks denote that a disc is not for audio use.
Boards requiring use of unleaded solder are printed with the lead free mark LF indicating the solder contains no lead. Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size. Unleaded solder has the following characteristics. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Caution: The printed pattern copper foil may peel away if the heated tip is applied for too long, so be careful!
Unleaded solder is more viscous sticky, less prone to flow than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. When repairing or servicing this set, connect the jig extension cable as shown below. Location of controls Sub Panel Assy CD Mechanism Block Main Board Speaker outputs sure seal connectors.
Audio outputs rear Power aerial relay control terminal. Telephone ATT control terminal. Parts for installation and connections Front panel case 1. Design and specifications are subject to change without notice.
Published by Sony Techno Create Corporation. The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts.
The flexible board is easily damaged and should be handled with care. The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick- up block. Therefore, when checking the laser diode emission, ob- serve from more than 30 cm away from the objective lens. Notice that the minus side of a tantalum capacitor may be dam- aged by heat. This label is located on the bottom of the chassis.
When replacing the chassis T. The following test discs should be used to check the capability:. These marks denote that a disc is not for audio use. Boards requiring use of unleaded solder are printed with the lead free mark LF indicating the solder contains no lead. Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.
0コメント